Heat pumps • Heating and cooling • Replacement planning
New Heat Pump Installation
Year-round residential heating and cooling planned around the building load, electrical service, indoor coil or air handler, controls and cold-weather performance.
Choose the building profile
The original equipment references remain available inside the two planning cards.
Single-family home planning
Whole-home capacity, duct and airflow review, outdoor-unit location, condensate and cold-weather operating strategy.
View original equipment reference →
Multi-family property planning
Compact equipment and distribution planning for apartments or multi-family spaces, including access and electrical limits.
View original equipment reference →Sizing note. Square footage is only a starting point. Final equipment selection must account for the building load, insulation, windows, ductwork or distribution, electrical service, fuel, venting, piping and manufacturer requirements.
What the installation plan includes
- Heating and cooling load review, including winter design conditions.
- Outdoor unit, indoor coil or air-handler compatibility and refrigerant-line planning.
- Electrical capacity, disconnects, controls, thermostat and auxiliary or backup heat strategy.
- Airflow, condensate management, startup, charge verification and delivered-temperature checks.
Prepare an accurate estimate
Send the service address, photos of the existing equipment and data plates, the approximate conditioned area, current utility type and any comfort or operating problems. Site access and code requirements are confirmed before final equipment selection.
Planificación en español
Planificamos bombas de calor para calefacción y aire acondicionado durante todo el año. Se revisan carga, ductos, electricidad, controles, ubicación exterior y rendimiento en clima frío antes de seleccionar el equipo.
Match heating and cooling to the building
Cyclone installs heat pumps in Westchester, Putnam and Yonkers.
A new heat pump has to serve both heating and cooling needs. Planning therefore considers the building load in both seasons, including winter conditions, rather than selecting an outdoor unit from floor area alone. Describe the existing system, the spaces it serves and the comfort problems you want a replacement to address.
Cyclone reviews outdoor-unit placement, indoor coil or air-handler compatibility, refrigerant-line routing and the available electrical service. Ductwork, airflow, thermostat controls and an auxiliary or backup heating strategy are also part of the planning scope. Space and access constraints may differ between a single-family home and a multi-family property.
For an estimate request, send equipment photos and nameplates, approximate conditioned area and information about the current system. The site review establishes the requirements before final equipment selection. Startup planning includes airflow, condensate management, charge verification and delivered-temperature checks. The equipment references on this page illustrate project paths; they are not a substitute for matching a complete system to the building.
Adapte la calefacción y el enfriamiento al edificio
Cyclone instala bombas de calor en Westchester, Putnam y Yonkers.
Una bomba de calor nueva debe atender calefacción y enfriamiento. La planificación considera la carga del edificio en ambas temporadas, incluidas las condiciones de invierno, en vez de seleccionar una unidad exterior únicamente por superficie. Describa el sistema existente, los espacios que atiende y los problemas de confort que desea resolver con el reemplazo.
Cyclone revisa la ubicación de la unidad exterior, la compatibilidad del serpentín o manejadora interior, el recorrido de las líneas de refrigerante y la capacidad eléctrica disponible. Ductos, flujo de aire, termostato y estrategia de calefacción auxiliar o de respaldo también forman parte de la planificación. Las limitaciones de espacio y acceso pueden diferir entre una vivienda individual y una propiedad multifamiliar.
Para solicitar una evaluación, envíe fotos del equipo y sus placas, superficie aproximada e información del sistema actual. La revisión del lugar establece requisitos antes de seleccionar los equipos. La puesta en marcha se planifica con revisión del flujo de aire, manejo de condensado, verificación de carga de refrigerante y medición de temperaturas de entrega. Las referencias enlazadas ilustran perfiles de proyecto; no sustituyen la selección de un sistema completo acorde al edificio.
Si todavía está comparando entre reparar y reemplazar, vea el diagnóstico y la reparación de bombas de calor.